| 1. | Combined with case analysis , this essay illuminates the actual application of the location selection method based on gravity method and discrete model
结合实例分析，说明基于重心法与离散模型的配送中心选址方法的实际应用。 |
| 2. | For this reason , the discrete model is used to solve the optimized place of distribution center on the basis of getting spare location by gravity method
为此在用重心法得到备选地点的基础上，引用离散模型解决配送中心的最佳地点问题。 |
| 3. | Contraposing issue of how to decide location - selection of depot in yinshan underground , the author used for reference and applied the center - of - gravity method to probe into and settle the issue
摘要针对银山井下库房如何选址决策的问题，作者借鉴并应用重心法探讨和解决该问题。 |
| 4. | When confirming the location of logistics distribution center by using gravity method , it is limited in the actual application , because the location selection method only takes into account traffic cost rate and freight traffic volume
摘要采用重心法确定物流配送中心的位置，由于选址因素只包括运输费率和货运量，在实际应用中受到很大限制。 |
| 5. | The software matlab is used to calculate the fuzzy system , the fuzzy system divide the voltage - reactive pane into nine fuzzy zone , in this way the domain - swing between closing domain is eliminated
该模糊推理系统的隶属度函数采用三角形隶属度函数，模糊推理采用mamdani型推理，非模糊化采用的是重心法，在设计时使用matlab为辅助进行离线计算。 |
| 6. | Optimization of 400v distribution network are traversed . selection address of transformer is realized with barycenter method and optimization network is realized with ga ( genetic arithmetic ) . then this two are considered together
然后详细研究了400伏配电网最优规划的方法，用重心法求实现配变选址，用基因算法实现网架优化，并将配变选址和网架优化统一考虑。 |
| 7. | Based on research of the fringe method , the midline method , the depth restrict method , and so on , the paper puts forwards new method of contour extracting - - the gray barycenter based on edge ( gbbe ) . contour extracting is kernel problem of slim
论文在分析了边缘法、中线法、基于骨架的灰度重心法、深度约束法等轮廓提取方法的基础上，对结构光图像法的核心问题一一光带轮廓提取，提出了一种新的光带提取方法? ?基于边缘的灰度重心法。 |
| 8. | Studied on floating avoiding method and the memory conflict regulating method to realize the real - time image capture . 2 . using four subpixel - locating methods to obtain the center of micro parts , which are template - matching method , core - shape method , centrobaric gray method , and edge - fitting method
利用模板匹配法、型心法、灰度重心法和边缘拟合法等四种亚像素定位方法实现了对零件中心位置的检测；利用图像旋转方法，进行了零件旋转角度定位研究。 |
| 9. | In this thesis a fuzzy control system used in voltage and reactive power auto regulatory device is designed based on the nine - zone controlling principle . in the fuzzy system , the fuzzy reasoning is mamdani method and the antifuzzy is centroid method . the software matlab is used to calculate the fuzzy system . the fuzzy system divide the voltage - reactive pane into fuzzy zone , in this way the domain - swing between closing domain is eliminated
论文对电压无功综合控制技术进行研究，针对传统九区域分区控制方法无视电压与无功耦合的缺点，结合变电站电压无功控制的实践经验，在传统控制方法上引入模糊控制，设计了基于模糊控制的电压无功综合控制系统。模糊推理系统中采用mamdani型推理，非模糊化采用重心法，设计中使用matlab进行辅助设计和离线计算。 |
| 10. | Modern logistics system simulate optimization this thesis in theory aspect , establish the mathematics model and bring up the calculate way using heuristics method to optimize the right conveyance problem in the simulative logistics system ; solution logistics the center choose problem , make use of the number analysis the method ( center of gravity method ) to proceed the optimization design solution to calculate ; the thesis furthest extrude put great emphasis on the logistics system production total cost had bigness affect and difficult to control over the problem of the manufacture and stock quantity make use of the matlab to bring up the simulative optimization design project separately with simple optimization algorithm and simplex method algorithm
现代物流系统仿真优化论文在理论方面，用物流系统仿真对运输优化问题运用启发式方法建立数学模型、提出算法；在解决物流中心选址问题时，利用数值分析法(重心法)进行优化设计解算。本文最为突出的是运用简单寻优技术的单纯形法利用matlab就物流系统中对总成本有巨大影响并难以控制的生产和库存数量问题提出可行的仿真优化设计方案。 |
