English translation for "屈服区"

yield region
yield zone

Related Translations:

屈服:  surrender; yield; bow to; give away; knuckle under; submit to 短语和例子迫使某人屈服 bring sb. to his knees; bring sb. to terms; 屈服于外界的压力 yield to pressure from outside; 他屈服于这种不公平的待遇。 he submitted to

塑性屈服:  plastic yielding

拉伸屈服:  tensile yield

屈服强度:  offset stressproof stressshear strengthyield intensityyield strengtrhyield stressyld yield strengthys yield strength

屈服曲线:  yield curve

屈服比:  yield ratio

体积屈服:  bulk yielding

屈服能力:  yieldability

屈服损坏:  yield failure

局部屈服:  local yielding

Example Sentences:

	1.	Yield will spread from the outer fibers inward until the two zones of yield meet . 屈服从外面纤维向里扩展，直到这二个屈服区相交为止。
	2.	The yield zones he found in polycabonate were slits extending ahead of the crack . 他发现聚碳酸脂中的屈服区是延伸至裂纹前沿的长条裂缝。
	3.	It is shown that : at the position of maximum bearing clearance , the non - yield region is attached to bushing , while at the position of 随着屈服应力的提高，未屈服区逐渐扩大，当达到一定值时，流场对屈服应力达到饱和状态。
	4.	The stresses and strain are analyzed by marc software ; the safety factors evaluated based on displacement , yield region ( connected ) and total energy criteria 应力和应变由marc软件分析计算得到；安全系数由位移变化、屈服区连通率和总应变能变化来评价。
	5.	Secondly , the steady and transient characteristics of concentric cylinder er clutch and plane er valve are studied with the consideration of yield . it can be found that when the extra electric field is suddenly applied , non - yield region in the clutch dose not generate synchronously . there is a retardation time which becomes shorter while the extra electric field becomes stronger 对圆桶型电流变离合器动力学特性的分析发现，在离合器关闭时突加电场瞬间，流场中并未瞬时产生未屈服区，而存在滞后时间，且随外加电场强度的增大而减小；电流变液屈服应力方程中，参数以2 . 0为界，和时，离合器动力学特性具有显著区别。
	6.	The calculation results indicate that the outboard of drum walls fall in plastic yielding at the same time the rising cooling water reaches the height of that point and the yield region becomes narrower and narrower when it comes closer to the circumferential strake weldments , which explains the reason coke drums experience bulging and cracks occur in the weld seams portions of shell to shell after long in service 计算结果表明：塔壁外侧在冷却水面到达的瞬间进入塑性屈服，筒节中部塑性屈服区较大，当靠近焊缝时塔壁的塑性变形区逐渐缩小直至消失，塔壁塑性屈服区的分布特点解释了塔体长期使用后发生鼓凸变形及简体与焊缝连接处产生裂纹的原因。

Similar Words：

"屈服强度" English translation, "屈服强度,软化强度" English translation, "屈服强度港作拖船" English translation, "屈服强度理论" English translation, "屈服强度下限" English translation, "屈服区域" English translation, "屈服曲面" English translation, "屈服曲线" English translation, "屈服上限" English translation, "屈服伸长" English translation